大家在查：安达利尔 ZM 尽管瘦削毡子如狼似虎内陷 -established 兆字节班吉 One-JAR

carburizing

美英 ['kɑːbjʊraɪzɪŋ]

n.渗碳；增碳；碳化
网络渗碳剂；渗碳处理；渗碳法

carburizing

carburizing

英-汉网络释义

carburizing

n.

1.渗碳

2.增碳

3.碳化

1

Steel for carburizing is usually a low-carbon steel of about 0 . 15% carbon that would not in itself responds appreciably to heat treatment .

用于渗碳的一般是含碳量约为 0.15%、本身不太适合热处理的低碳钢。

3

CYCLE TIME : Amount of time product spends in a furnace at specified temperature for the purpose of carburizing or hardening product .

周期：产品在炉中某特定温度下渗碳或硬化所需要的时间。

4

The feature of the microstructure of the silicon - aluminizing coating and its anti-carburizing property were analyzed and studied .

分析了铝硅共渗层的组织特点，研究了处理层的抗渗碳性能。

5

The amount and the depth of carburizing on the casting surface can be obtained approximately by a calculating formula .

给出了铸件表面增碳大小及增碳层深度的近似计算公式。

7

Carburizing, cyaniding, and induction hardening are some of the processes commonly used to produce the case hardening effect.

碳化、氰化、感应淬火是局部淬火中经常使用的处理方法。

8

The carburization rate can be increased 20% compared with the conventional carburization process by using RE catalyzed carburizing .

采用改进型稀土催渗剂进行渗碳后，与常规渗碳工艺相比提高渗碳速度 20%；

10

The better technological process now is the step control of carbon potential during carburizing .

目前最佳渗碳工艺方法，是在整个渗碳过程中对碳势进行台阶式控制。

12

and then carrying out molding and pre-sintering, carrying out mechanical press -fitting and the sintering-soldering , and finally carburizing .

接着进行成形和预烧结，然后进行机械压配和烧结焊，最后进行渗碳即可。

13

Nonsymmetrical carburizing may also contribute to distortion .

渗碳的不对称也可能导致变形。

16

Pack carburizing consists of placing the parts to be treated in a closed container with some carbonaceous material such as charcoal or coke .

固体渗碳的方法是将要处理的零件与木炭或焦炭这些含碳的材料一起放入密闭容器。

17

19

The residual life of the tubes is estimated based on the carburizing damage analysis.

在考虑渗碳损伤的前提下对炉管的剩余寿命进行了评估。

21

Two carburizing processes were adopted, before or after the hydrothermal reaction.

进行了水热前和水热后两种渗碳工艺研究。

23

The method of eliminating carbon can solve availably carburizing defect of steel casting was proved by practical production .

实践证明这种工艺方法可有效地解决铸钢件的增碳缺陷问题。

24

The sample of carburizing makes the component and hardness analysis .

对渗碳后的试样停止了成分和硬度剖析。

25

This article recommends the process of direct quenching after carburizing for sucker rod pump liners .

介绍了抽油泵衬套渗碳后直接淬火处理工艺。

26

The low-temperature RE carburizing technology is explored by a series of tests .

通过一系列试验，摸索出利用稀土低温渗碳技术。

27

Effect of silicon on microstructure and properties of meta-bainitic carburizing steel were studied .

研究了硅对准贝氏体渗碳钢渗碳组织与性能的影响。

28

So RE slat liquid carburizing may replace poisonous cyanide slat bath or "603 " slat liquqid carburizing .

可取代剧毒的氰盐和微毒的 “603 ”盐浴渗碳。

30

repeatedly forged iron , based on ancient block of iron also find the experience of carburizing Cheng Gang, this is the first steel to steel .

在反复锻打铁块的基础上，古人又找出块炼铁渗碳成钢的经验，这种钢地就是最早的钢。

热词推荐

大家在看