大家在查：够受避重就轻密特拉仇家陈希演变过程座城毫无用处 Seube Casanova

brazing

美 [breɪzɪŋ]英 [breɪzɪŋ]

v.【机】(用锌铜合金)焊接；用黄铜制造[镶饰,镀]
网络铜焊；硬焊；钎焊

第三人称单数：brazes 现在分词：brazing 过去分词：brazed

brazing

英-汉英-英网络释义

brazing

铜焊

钢丝绳_百度百科 ... 1．8．1 对焊 electric butt welding 1．8．2 铜焊 brazing 1．8．3 插接 twisting ...

硬焊

硬焊（brazing）是一种焊接方式，将熔点低于欲连接工件之熔填料(钎料)加热至高于熔点，使之具有足够的流动性，利用毛细 …

钎焊

耐热铁素体409HP_钢管知识_资讯_中国钢管信息港 ... 焊接（ Welding）钎焊（ Brazing）可用性（ Availability） ...

硬钎焊

焊接英语词汇 - wuhelo100的日志 - 网易博客 ... 局部干式水下焊 localdryunderwaterwelding 硬钎焊 brazing 软钎焊 soldering ...

焊接

「焊接(brazing) 」与套管34永久地结合在一起，而套管34两端的螺纹则与轴承总成的两个螺纹元件46、50固定在一起，若将一 …

银焊

自动银焊（Brazing）机检测设备辅助设备材料 LED检测设备 RoHS检测生产治具自动组装检测系统 ICT 在线测试仪 ICT 在 …

软钎焊

焊接工艺方法代号及其符号含义... ... WS——wave soldering—— 波峰钎焊 B——BRAZING—— 软钎焊 BB——block brazing—…

例句：

The traditional method that has long been used to attach segments to the steel core is brazing .

传统的方法是用已久的附加部分是钢钎核心。

Unfortunately, the brazing performance of Si-Al series alloys was found to be very poor due to very high silicon content .

然而，喷射成形硅铝系合金中硅含量很高，其焊接性能较差。

Brazing is the main processing methods of heat transfer, and also is a determining factor of affecting the heat transfer effect .

钎焊是换热器的主要加工方法，也是影响换热效果的决定因素之一。

Rated internal pressure is that of the tube being joined. While solders can be used , brazing alloys are recommended .

H 额定内部压力是所连接的管道额定内部压力。如果可以采用焊料，则推荐使用铜焊合金。

Also can be used for brazing steel and stainless steel, hard alloy of flux .

也可作钎焊钢及不绣钢、硬质合金的助熔剂。

It indicates the strong retention of brazing alloy to diamond grits and the longer service life of the wheel .

这表明钎料合金对磨粒的高强度把持和砂轮的高耐用度。

It may be attached by the use of a shrink sleeve , adhesive , brazing or welding .

也可使用收缩膜套、粘合剂、铜焊或焊接，使其连接。

The system set the design and management of brazing process as a whole .

该系统集钎焊工艺设计和工艺管理为一体。

The results of performance testing of brazing show that the modificatory fluxes have reached the level of the same foreign products .

测试结果表明，改性后的银钎剂已达到国外同类产品的水平。

The reasons are given why weak carbonizing flame of oxyacetylene is used for heating and why brazing seam area can't be polished .

论证了加热时氧 ——乙炔焰用微碳化焰的原因及焊缝结合区不能采用抛光的道理。

Effects of fillers and brazing parameters on mechanical properties and microstructures of brazed joints were investigated .

研究了钎料类型及钎焊工艺对钎缝接头力学性能与微观结构的影响。

When brazing dissimilar metals you need to take the coefficient of expansion when looking at joint clearance at temperature.

当不同金属钎焊时，必须考虑他们的焊接系数？

The effects of technological factors of wide clearance brazing, on formation and microstructure of joints are investigated in this paper .

本文研究了大间隙钎焊工艺因素对接头成形与组织的影响。

Fins are attached to the plates by a mechanical fit, gluing, soldering, brazing, welding, or extrusion .

翅片靠机械配合、粘结、软焊、硬焊、焊接或挤压附着在板上。

ALUMINIUM AND ALUMINIUM ALLOYS . WELDING, BRAZING AND BRAZE WELDING . BASE MATERIALS AND SELECTION OF FILLER MATERIALS.

铝和铝合金 .焊接、硬钎焊和钎焊 .基础产品和焊条的选择

The primary purpose of this research is focused in vacuum brazing SP-700 high-strength titanium alloys using various Ti-based braze alloys .

本研究主要的目标在于以多种钛基填料真空硬焊接合 SP-700 高强度钛合金。

In the paper, the research status of brazing joint strength between oxide ceramics, nitride ceramics, carbide ceramic . . .

分别对氧化物陶瓷、氮化物陶瓷、碳化物陶瓷、碳氮化物陶瓷与金属钎焊接头强度的研究现状进行了综述。

brazing

brazing

铜焊

硬焊

钎焊

硬钎焊

焊接

银焊

软钎焊

热词推荐

大家在看