大家在查： afterbirth hectares Payout 投稿 jugglers 一经 wisteria 盖亚水袖 Maldives

挠曲

na.flexure; bend; under load
网络deflection; Bending; flexing

挠曲

英-汉网络释义

挠曲

deflection

汽车英语2 - 乔木的日志 - 网易博客 ... Defectometer 探伤仪 Deflection 挠度；挠曲； Deflection ratio （轮胎）下沉率 ...

Bending

民航专业常用词汇指南(ME)[1]_百度文库 ... below 在…的下面 bending 弯曲挠曲 black 黑色 ...

flexure

冶金(Metallurgy)专业词汇(D-H) - 不锈钢世界 ... flexural stress 挠曲应力 flexure 挠曲 floating die 浮沉模 ...

flexing

《Friends》词汇表B ... bandage n. 绷带 flexing 挠曲, 可挠性 bathrooms n. 浴室, 盥洗室 ...

buckling

冶金词汇英语翻译(A-G) ... buckled sheet 波纹钢板 buckling 挠曲 buckling load 压弯临界载荷 ...

deflexion

矿业工程专业词汇英语翻译(D-H) -亿城英语 ... deflector brattice 转向风障 deflexion 挠曲 deflocculation 反凝絮 ...

warping

地质学专业英语词汇(35) ... 囊状矿脉 chambered vein 挠曲 warping 挠曲；单斜挠褶；弯曲 flexure ...

例句：

It was also found that the flexural strength and shear strength can be satisfactorily predicted based on the maximum pit depth .

利用平均最大孔蚀深度来估计剪力强度与挠曲强度，可得令人满意的结果。

The corresponding lateral deflection is determined using summation of its flexibility sources of bending , shear and slip .

墙体的侧向位移由挠曲位移，剪力位移与滑移位移这三个部分所组成。

In the material mechanics , the deflection of metal girder is a minute movement , and can't be measured using the normal regulation.

在材料力学中，金属梁的挠曲线是一个微小的位移分布，无法用常规测量方法精确测量。

Basin is curved by pressure then slides away down the laminar while mountain extends sideway then thrusts and nappes up.

（盆）挤压挠曲、顺层滑脱 -（山）侧向扩展、逆冲推覆。

It will decrease the maximum axial stress of the lining , but it will increase the maximum shear stress and flexural stress .

开挖引致的松动区减少围岩劲度，将减少衬砌轴向应力，但增加剪应力及挠曲应力。

Leather - Physical and mechanical tests - Determination of flex resistance by flexometer method .

皮革 .物理和机械试验 .用挠曲计法测定抗弯性

Lateral displacement and bending of inclined pile could be reduced with the introduction of pile cap .

承台有助于减小倾斜桩的水平位移与挠曲。

A research method of the large deflection of the throttle slice of the hydropneumatic spring was presented .

提出了一种研究油气弹簧环形阀片大挠曲变形的方法。

There may be additional zones of flexure within the device .

在该装置中可具有其它的挠曲带。

The flexural strength is determined by a sectional analysis, and the shear strength is predicted using the softened strut-and-tie model .

挠曲强度可用规范公式来决定，而剪力强度则采用软化压拉杆模型来计算。

We present a method for computing annular slice deflection . The physical model of throttle slice was built.

提出环形阀片受相关载荷作用时挠曲变形量的一种研究方法。

The viewing angle is dependent on the geometric parameter of grating surface, the flexoelectric coefficients, and the anchoring strength .

视角明显依赖于栅状表面几何参数、挠曲电系数和锚定强度。

Offers good flexibility when fitting roof-mounted accessories .

安装顶部附件时，提供了良好的挠曲性。

A research method for the deflection of throttle slice under the local distribution of variable load is presented .

提出了减振器环形节流阀片受局部变载荷作用时挠曲变形量的一种研究方法。

Behavior of RC members respectively subjected to moment, shear force and axial or plus bending.

RC 构件受挠曲、剪力及轴力或加弯矩之行为；

Footwear - Test methods for uppers and lining - Flex resistance .

鞋类 .鞋帮和鞋衬的试验方法 .抗挠曲性

Methods of test for screed materials - Part 2 : determination of flexural and compressive strength.

找平层材料的试验方法 .第2 部分：挠曲强度和抗压强度的测定

However , under heavy load the shaft may deflect excessively .

但是，在重载作用下，轴会发生过度挠曲。

挠曲

挠曲