大家在查： murdering 金融资本伙天坑金利 cots dancefloor monitor process 提心吊胆地 duty officer

铣

n.〈书〉bright metal
v.mill
网络milling; CNC; milling machine

铣

英-汉英-英网络释义

铣

milling

电力英语技术术语|国电海明 ... 2744.割 cutting 2745.铣 milling 2746.刨 planning ...

CNC

　　8.技术采购:3名, 熟悉机械加工车、铣（CNC）、磨等制造工艺；有很强的沟通能力及谈判技巧；忠诚、可靠、独立的个性和建 …

milling machine

模具英文_百度文库 ... wire cut 线割 milling machine 铣 Cut steel 开料蚀纹 ...

millings

台湾V型皮带轮 - V型皮带轮专业制造商和... ... 冲压，车削，镟，铣， millings， ...

face milling

… 护费较冷作高 (D) 热作所须 … 铣 (face milling) 作业中，铣削 300mm 长之 … 接 4. 若铸铁中之石墨主要 … ) 半导体制程中…

qtfq

Name=UC五笔MaxCodes=4 MaxElement=1 ...... ... 铤 qtfp 铣 qtfq 橥 qtfs ...

CFB

互联网_Unicode和GB2312编码表_软件世界网 ... E2 EEF9 铢 94 E3 CFB3 铣 94 F4 BCE4 间 95 ...

例句：

A mill is usually used to remove junk in the hole or to grind away all or part of a casing string.

铣鞋通常用于除去井下的碎屑或者研磨掉整个或部分套管。

Used for milling processing of the profile bending parts of aluminum curtain wall .

适用于铝塑幕墙型材，实现型材折弯处的铣槽加工；

With it pinions can be machined with hob or single-tooth indexing, also can with shaft cut-in and radial cut-in method .

可采用逆铣和顺铣方法加工齿轮，可以轴向或径向进行加工。

Permanent packers are constructed of materials that are easy to drill or mill out .

永久型封隔器由容易钻掉或者磨铣掉的材料制成。

Draw the pattern of the drawer fixer on the dense board , then cut the pattern out with the fretsaw machine .

把拉手图案画在密度板上，然后用线锯机切割，如果要孔的则用铣钻床打孔，并按上螺帽。

The book block milling back edge finish depends on the size of the angle in and out of frezer.

书芯铣背的边缘光洁度取决于铣刀进出角度的大小。

In this case , the amount of milling back , please! --the thunder from the out-of-mouth parts of the book set.

在此情况下，铣背量多了，就必然划破外帖书芯订口部位。

Due to the structure of the bookbinder , plus different machine , you do not use slot often out of quality issues .

由于胶订机的结构不同加上机器操作、使用不当，铣槽常会出质量问题。

The root of the quality , not lack of milling back , and are made of plastic difference not glued milling and broken pages .

究其质量原因，并非铣背不足所致，而是胶质差没有粘牢铣断的书页。

The pipe is too hard to be milled easily which makes the efficiency of it to be low .

钻杆做为落物，其硬度较高，磨铣不易切削，磨铣效率极低。

Up milling (conventional milling). In up milling the workpiece is fed against the direction of cutter rotation , as shown in Fig . 12. 3a.

逆铣（传统铣削）：在逆铣中，工件逆着铣刀转动的方向进给，如图 12.3a 所示。

binding package on my computer for milling back , slotted-bed down to make it to the back of the book .

将胶订包本机上的铣背、开槽台下降，使其接触不到书背。

If milling back and dehairing deep enough , will definitely affect the infiltration of rubber , resulting in off the page, the leaflet.

若铣背和打毛的深度不够，必然影响胶的渗透，从而造成脱页、散页的质量缺陷。

'We're still only at the beginning , ' says Tang Sixian, the Sanya Tourism Development Board's deputy director .

三亚旅游产业发展局副局长唐嗣铣说，“我们还是刚刚起步。”

the amount of milling back on either side of the inconsistent due to off the page, the page quality .

两边铣背量不一致引起的掉页、散页质量问题。

A milling hole main shaft, the chamfer main shaft and a main electric motor are all installed on a revolution body .

铣孔主轴、倒角主轴和主电机均安装在回转体上。

Milling back, slot is to determine the binding of books and periodicals can be an important step in the bonding bridgeis .

铣背、开槽是决定无线胶订书刊能否黏结牢固的重要环节。

do not exhaust will create the most in the page does not open or milling milling open enough .

若书帖不排气就会造成最里页铣不开或铣开不够。

In the case of junk , the metal must be broken into smaller pieces to facilitate removal from the wellbore so that drilling can continue.

当铣鞋用于除去井底的碎屑时，金属必须被破碎成很小的片、块，以有助于从井眼内除去。

Avoid excessive tip segment, the bottom slot , so that the gap is too small for the slot bottom note glue .

避免刀头过尖，铣槽底部缝隙太小，使沟槽底部注胶不满。

the book block of cryomacrotoming must be a book page in each of the milling machine into leaflets .

书芯背的铣削必须将每一帖书页铣成单张。

The circulated fluids should be capable of removing the milled material from the wellbore .

循环液应能从井筒中去除磨铣后的物料。

热词推荐

大家在看

man , . 's " you what ? : - say after of as then a with by 4th your