大家在查：赵晏临王陴 243个 skelp 索菲·穆特 Yuffie glycerides 绝对是 Myristicae 白一世

进给量

n.feed
网络Feed rate; amount of feed; fz

进给量

进给量

英-汉网络释义

进给量

n.

1.feed

2

Through the numerically controlled unit head, the transverse feed amount and feed speed of a cutting tool are accurately controlled .

本发明使刀具的横向进给量和进给速度得到了精确控制。

4

With the hydraulic control system its cutting speed can be adjusted randomly by the size and the thickness of the caliber .

它采用液压进给，进给量切削速度可根据口径大小、臂厚随意调整。

6

Hardness, flatness and surface roughness of the roll barrel can be ensured by controlling the speed and cutting feed amount.

通过控制速度与进给量来保证辊身硬度、平直度及表面粗糙度要求。

7

The results showed that: the depth of cut had the main influence on cutting force followed by feed rate and cutting speed in turn .

研究结果表明：切削用量中背吃刀量对主切削力的影响最大，进给量次之，切削速度对主切削力的影响最小。

8

Emphatically researched on tool cutting process, a blunt cutting edge and feed rate of the processing quality is analyzed .

分析圆弧刃刀具切入过程、切削刃钝圆和进给量对加工质量的影响。

9

The test device through the digital display table shows the number of feed or feed circle .

该检测装置通过数显表显示进给圈数或进给量。

10

In grinding operation , feeding and operation speed can be adjusted at random .

在磨削过程中可任意调节进料速度和进给量；

12

Finally turning with higher feeds leads to even higher process forces and hence , to higher roundness values.

进给量的增加会导致更高的切削力，因此圆度值也增加；

13

In the rolling process, must be reasonable to control the feed roll .

滚压过程必须合理控制滚压进给量。

14

In this paper, effects of depth of cut and feedrate on mechanical properties of metallic fiber are investigated by spinning bit.

研究了用自旋转车刀加工金属纤维时，切削深度和进给量对纤维力学性能的影响。

17

Also call Film advance . Paper feed .

亦称菲林前向量，相纸进给量。

19

Machine Tools; Feeds for Machine Tools; Nominal Values, Limiting Values, Transmission Ratios

机床 .机床的进给量 .额定值 .极限值 .传动比

20

Mathematic Way of Numerical Control Programming for Feed of Flexural Wood Bending Robot

弯曲木加工机器人进给量数控编程的数学方法

21

The Study of the Application of the High-Speed and Heavy-Cutting Special Fixture of Machining Cylinder Block of Milling Machine

加工柴油机机体大进给量高速强力铣削专用夹具的应用研究

22

Using resection in large feeds turns the long and thin axle

用大进给量反向切削法加工细长轴

23

Step feed amount of each stroke of the table (stepless regulation)

工作台每行程断续进给量（无级变速）

24

Study on Improving Micro-hole Machining Quality by Varying Feed Rate Vibration Drilling

变进给量振动钻削提高微小孔加工质量的分析

26

An Algorithm for Maximum Feed Evaluation of Ball-nose End Mills with Indexable Inserts

可转位球头立铣刀最大进给量算法

27

Range of longitudinal automatic feeding

纵向自动走刀进给量

28

Range of longitudinal and cross mechanical feeding of table

工作台纵、横机动进给量范围

29

The Influence of Feed Rate and Pick Feed on Surface Roughness in High-Speed Milling

高速铣削加工中进给量和进给间隔对表面粗糙度的影响

30

Control for buffing step of wedge belt peeling and buffing machine

多楔带磨削机磨削进给量的控制

热词推荐

大家在看