大家在查： zithiol 伯明奥库卡山老闆得不 all-conquering karbofos EricForsman 殡仪馆说话 Flemish

翻边

n.flanging; tile key
网络flange; upsiding down edges; STUB END

翻边

英-汉网络释义

翻边

n.

1.flanging

2.tile key

2

FEM has been used to simulate and analyze the high pressure rubber forming process of part with flange bending.

利用有限元技术，对凸翻边钣金零件的高压橡皮成形过程进行模拟分析。

3

the side edge of the hand disc is provided with a flanging , the hand disc is surrounded by air inlet holes .

所述的手拉盘侧边设有翻边，所述的手拉盘周围设置有进气孔。

7

9

The difference of analysis and experiment results of flanging height is due to the mid-surface is moving to the center of bending curvature.

翻边高度理论和试验间存在偏差是由于中性层向内移动所致。

10

Technological experiments of flanging process were performed with cold-rolled steel sheet (SPCC) under ordinary lab condition .

用普通冷轧钢板 SPCC 在一般实验条件下进行了翻边工艺试验。

13

The flange cut that consequently its sub implements very easily in clean is in (namely the brim ) observe .

因而它的胶层很轻易在洁具的翻边切割处（即边缘）观察到。

14

The size of upsetting-burring punch and angle of support panel also have great impacts on the upsetting-burring.

镦粗凸模尺寸以及下支撑板斜角对镦粗翻边有较大的影响。

15

Lightly padded cuff at the top of the upper that keeps out debris .

很松地填补在鞋帮顶部翻边处，以防止碎石进入。

16

The phase of the fed-back signal is sometimes inverted , producing another variation on the flanging sound .

美联储回信号的相位有时倒，生产翻边声音的另一个变体。

17

The simulation results show that, the height of upsetting-burring is higher than that of traditional burring.

模拟结果表明：厚板局部镦粗翻边较传统翻边的翻边高度明显提高；

19

Pediatric tracheostomy tubes are usually not cuffed .

儿科用的气管切开术插管常常没有管口的翻边。

20

But if , for example , you use your flaring tool only a couple of times a year, you should refresh your recollection before each use .

但是，如果，例如，您使用您的翻边工具仅一年几次，你应该在每次使用前，刷新你的记忆。

21

The machining processes basically has the following four steps: tensile, trimming and punching , Flanging and plastic, cut and flanging .

其加工工序主要有：拉延，修边冲孔，翻边整形和切开翻边。

22

For the necessity of auto 's welding and assemble , mostly all of automobile panels have the flanging forming .

由于焊接和装配的需要，大部分汽车覆盖件都要进行翻边成形。

24

A large deformation elastic plastic FEM model is employed to simulate the stretch flanging of V shaped sheet metal parts .

采用弹塑性大变形有限元方法研究了几何形状和材料参数对 “V ”型零件翻边的影响；

25

It is our invariable pursuit that "Researching and developing fin die with high flange, high precision and low cost " .

“致力于高翻边，高精度，低成本模具的研发 ”，是我们易和公司的毕生追求。

26

The flanging -sizing die structure of the exo-skeletal was improved , using auto-half block, solved the difficult problem of part out off die .

改进了的旧的骨架翻边整形模，采用自动哈夫成形，解决了零件出模困难的问题。

27

Based on previous studies of flanging , the factors that influence the quality of flanging were the in-depth studied in this paper .

本论文在前人研究的基础上，对影响翻边成形质量的因素进行了深入的研究。

28

Loose-fitting trousers with elastic cuffs ; worn by athletes .

有弹性翻边的宽松的裤子；供运动员穿着。

30

Visor skate winter cuffed hat , ski , beanie, cap, light gray.

护目镜滑板冬季翻边帽，滑雪，无檐小便帽，帽，光。

热词推荐

大家在看